Wacom SD-311E Manuel d'utilisateur télécharger pdf (Page 33)

COMPUTER VIDEO

A JA

1054

D-SERIES MINIATURE CONVERTERS

www.bhphotov ideo.com

D10CE

SDI to Analog Component and Composite Converter

The D10CE provides excellent quality

10-bit conversion of SDI to simultaneous

component and composite video.

Component outputs are user

configurable to Y/Pb/Pr, Betacam, or

RGB (or composite Y/C). The composite

output is configurable to composite

video or sync. The component and

composite outputs are completely independent including optimum

chroma filtering for each and independent pedestal configuration.

The D10CE also features an exclusive PLL jitter filter/memory to reduce

the effects of SDI jitter on the output analog video. This feature, along

with the precision 4x oversampled D/A filters, provides the highest

quality analog outputs including very low phase noise in composite

outputs. The D10CE also provides two re-clocked, loop-thru SDI outputs.

All functions are user configurable via external dip switches.

D10CE

(Mfr # D10CE • B&H # AJD10CE) ..................................................................559.95

D10C2

SDI to Analog Component or Composite Converter

The D10C2 provides excellent-quality

10-bit conversion of SDI to analog

component or composite video at low

cost. In component mode, outputs are

user configurable to Y/Pb/Pr, Betacam,

or RGB. In composite mode, it provides

two composite outputs and an S-Video

output. The D10C2 also provides two

re-clocked, loop-thru SDI outputs and a composite sync output

(component mode). All functions are user configurable via external

dip switches.

D10C2

(Mfr # D10C2 • B&H # AJD10C2) ..................................................................449.95

D10AD

Analog Component or Composite to SDI Converter

The D10AD provides excellent-quality

10-bit conversion of analog component

or composite video to SDI (four outputs)

with EDH. The D10AD accepts Y/Pb/Pr,

Betacam, or RGB component inputs or

composite (automatic NTSC/PAL) and

S-Video inputs. The D10AD features a

4-Line Adaptive Comb Filter for high-

quality decoding of composite sources. The comb filter can be switched

to 2 line or notch modes for minimum delay requirements. Video

format, AGC mode, and color bar generator, and pedestal are user

configurable via dip switches.

D10AD

(Mfr # D10AD • B&H # AJD10AD)................................................................554.95

D10A

Analog Component to SDI Converter

(with Separate Sync Input)

A favorite of professional video

engineers, the D10A provides superior

quality component-only analog to

10-bit SDI. The D10A is factory-set to

accept either Y/Pb/Pr, Betacam, or

RGB in 525 or 625 line formats,

converting the analog component

signal to10-bit SDI. The D10A has

three BNC’s for component input, one external sync input, and three SDI

(two loop-through) outputs. Input formats can be reset by internal

jumpers and level/gain controls. Normal/Wide V-blanking.

D10A

(Mfr # D10A • B&H # AJD10A) .......................................................................759.95

D10CEA

SDI to Analog Audio and Video Converter

The D10CEA converts SDI video with

embedded audio to 10-bit component

or composite analog video and 4-channel

balanced analog audio. Video outputs

can be configured as YPbPr, RGB,

composite or S-Video. The 4-ch analog

audio outputs can be wired in a balanced

or unbalanced configuration. The 4 audio

output channels can be selected as group1-4 from SMPTE embedded

audio. Audio level has 4 settings. Audio and video output connections

are available on a 25-pin “D” subminiature connector – a break-out cable

is supplied. All video/audio configuration is done by external dip switch

selection. This versatile, low-cost, miniature monitoring solution also

outputs two re-clocked loop-thru SDI outputs.

D10CEA

(Mfr # D10CEA • B&H # AJD10CEA)...........................................................679.95

D10C

Composite Digital (D2/D3) to Composite Analog,

or SDI to Component Converter

Providing excellent quality 10-bit digital

to analog conversion at low cost, the

D10C is useful for D/A conversion,

high-quality monitoring, or adding an

SDI input to VCRs, workstations, or other

analog video equipment. The D10C

automatically works with component or

composite SDI inputs in 625 or 525 line

formats. Featuring one SDI input with two re-clocked, loop-thru SDI

outputs, the D10C also acts as a distribution amplifier/repeater.

The D10C provides a component analog output for component SDI

inputs (D1), a NTSC output for 525 line composite SDI inputs (D2, D3),

and a PAL output for 625 line composite inputs SDI (D2, D3).

D10C

(Mfr # D10C • B&H # AJD10C)........................................................................684.95

1 2 ... 28 29 30 31 32 33 34 35 36 37 38 ... 123 124

Commentaires sur ces manuels

Pas de commentaire

Wacom SD-311E Manuel d'utilisateur Page 33

Commentaires sur ces manuels